All Paver Services All Concrete Services Pavers — Ocoee Pavers — Winter Garden Concrete — Ocoee Concrete — Winter Garden Our 38-Point Process Warranty About Blog Contact Call: (689) 356-6292

PAVER CARE · CENTRAL FLORIDA · 2026

Paver Maintenance in Florida: Ants, Weeds, Mold and Joint Sand

Florida pavers need full joint sand, good drainage and a few dry-season jobs more than constant scrubbing. Here is what to do about ants, weeds, algae and white haze, and when to call a pro.

Updated November 17, 2026

L
Luan Silva · Founder, Ocoee Concrete & Pavers

Ocoee-based paver and concrete company, founded 2020. Pricing and methods below reflect how our crew quotes and installs work in West Orange, Osceola, Lake and Polk counties in 2026.

How do I stop ants and weeds in the joints between pavers?

Keep the joints full and hard: sand packed to within about 1/8 inch of the paver surface leaves little room for ants to tunnel or for weed seed to root. Most joint problems start when the sand washes out, so the fix is usually sand, not poison.

Ants, including fire ants, like the loose, dry sand under and between pavers. You will see small mounds of sand pushed up along a joint. Weeds take the same opening: wind and birds drop seed into a low joint, and Central Florida rain and heat do the rest.

Polymeric sand or regular joint sand: which one should I use?

Polymeric sand is the usual choice for driveways and patios in Central Florida because it hardens after it is wet and resists washout, ants and weeds better than plain sand. Regular masonry or paver sand stays loose, drains freely and needs topping up more often.

Polymeric sand is fine sand blended with a binder. You sweep it into dry joints, remove every bit of dust from the paver faces, then mist it so the binder activates. It then needs a dry window to cure. Our crews finish new installations with polymeric sand as part of the standard method.

Joint sandStrengthsTrade-offs
Polymeric sandLocks in place; resists washout, ants and weedsNeeds dry, clean joints and a dry curing window; leaves haze on the surface if it is not cleaned off; very low permeability
Regular paver or masonry sandInexpensive; drains freely; easy to refillWashes out in heavy rain; ants and weeds move in; refill every year or two

One caution worth knowing: UF/IFAS Extension has noted that polymeric sand is close to impermeable, which can conflict with Florida-Friendly Landscaping goals for stormwater, and has suggested permeable joint materials in some settings. For a typical home driveway or patio that sheds water to the street or a swale, polymeric sand is still common practice. If you want more infiltration, ask us about permeable joint material for your layout.

How do I remove black mold, green algae and efflorescence from pavers?

Start with a gentle wash and a paver-safe cleaner: algae and mold respond to a diluted oxygen or mildew cleaner, and efflorescence (white haze) needs an efflorescence remover. Always test in a small corner first and rinse the planting beds around the area.

Black and green growth. Shade, sprinklers and the Florida rainy season keep pavers damp, and that is what algae and mold need. They are mostly a cosmetic and slip problem. Scrub with a soft brush and cleaner, let it sit per the label, then rinse. Then cut back what holds moisture: trim shrubs, aim sprinkler heads off the pavers and keep gutters and downspouts from dumping across the surface. If anyone in your household has asthma or a mold sensitivity, wear a mask or hire the work out.

White haze (efflorescence). This is mineral salt carried to the surface by moisture, most often in the first year or two on new concrete pavers. It is not mold. It usually fades by itself with time, and an efflorescence cleaner that is approved for your pavers speeds that up. Do not seal over it: sealer traps the haze and can make the surface look cloudy.

Can I pressure wash pavers, and will it wash the sand out?

Yes, you can pressure wash pavers, but use a wide fan tip, keep the pressure moderate (generally about 1,500–2,500 PSI for concrete pavers) and expect to re-sand afterward, because the water strips joint sand along with the dirt.

After washing, let the pavers dry, refill the joints, then seal if you plan to. The proper order is: clean, treat stains, rinse and dry, re-sand, then seal. Pressure washing is why joint sand "disappears" after a cleaning; it is not a sign that anything failed. Sand also washes out on its own when heavy rain runs across the surface or a downspout or sprinkler keeps hitting one spot.

How often do pavers need to be re-sanded?

Most Central Florida driveways and patios need regular joint sand topped up every 1–3 years, and polymeric sand typically lasts about 5–8 years before it needs a refresh. Check after every rainy season and after any pressure washing.

Look at the joints. If you can see the beveled edge of each paver sitting in a deep, open joint, sand has dropped. Joints should sit close to the top of the bevel. Low joints let pavers rock slightly under traffic, chip at the edges and invite ants and weeds.

When polymeric sand has worn out, we sweep out what remains, refill with new sand, compact, clean the faces and activate it. On our price sheet a joint-sand refresh typically adds about $250–$500 to a cleaning job, and paver cleaning plus sealing runs about $1.00–$1.75 per sq ft installed (2026, typical range; final price after an on-site estimate).

What is a month-by-month paver maintenance calendar for Florida?

Plan the bigger jobs for the dry months, October through May, and use the rainy season, June through September, for light checks only. Sealer and polymeric sand both need a few dry days to cure, which is hard to find in a summer afternoon-storm pattern.

WhenWhat to do
October–NovemberCheck joint sand after the rainy season; deep clean if algae built up; refill joints
December–FebruaryBest window for cleaning, re-sanding and sealing; cooler, drier weather helps curing
March–MayPull early weeds, treat ant mounds, finish any sealing before summer
June–SeptemberRainy season: rinse with a hose, sweep, watch for new mounds, trim plants shading the pavers; avoid sand and sealer jobs
Year-roundKeep sprinklers and downspouts off the pavers; sweep leaves; rinse pool chemicals off the deck

If you sealed in the last couple of years, reseal on the schedule in our paver sealing guide; the interval depends on sun, traffic and the sealer type.

Can I do paver maintenance myself, or should I hire a company?

You can handle sweeping, light weed pulling, hose rinsing and small joint refills yourself. Hire a crew for large-area pressure washing, polymeric sand, stain removal and anything involving sealer, because mistakes in those steps are visible and hard to undo.

TaskDIY?Why
Sweeping, hose rinse, pulling weedsYesLow risk and regular
Topping up regular joint sandYesInexpensive and forgiving
Fire ant colony in a jointYes, with a labeled productFollow the label; refill the joint afterward
Pressure washing a full drivewayPossibleStripes and etching happen easily; sand has to be replaced
Polymeric sand refreshHireHaze if the faces are not cleaned; needs a dry window
SealingHireBlotchy or cloudy finish if the pavers are damp or the product is wrong

When is it a base problem instead of a maintenance problem?

When the trouble keeps returning after cleaning and re-sanding, or when pavers move, rock or sink. Those signs point at drainage or base erosion, not dirty joints, and no amount of sand fixes them.

See our paver repair service for how settled areas are reset on a rebuilt base. If the surface just needs a refresh, ask about paver cleaning and sealing. We offer free written estimates and work seven days a week, and you can read our standard installation method on the process page.

Paver Maintenance FAQ

Why are ants coming up through my paver patio?

Ants nest in the loose sand under and between pavers because it is warm, dry and easy to dig. Brush the mounds flat, treat the colony with a product labeled for fire ants, and refill the joints with fresh sand. Hardened polymeric sand leaves less room for them to dig.

What is the white haze on my new pavers?

White haze on new concrete pavers is usually efflorescence, a mineral salt that moisture carries to the surface. It is harmless, often fades over a year or two, and can be removed with an efflorescence cleaner. Do not seal over it, because sealer can lock the haze in.

What PSI is safe for cleaning concrete pavers?

Concrete pavers generally tolerate about 1,500–2,500 PSI with a wide fan tip or a surface cleaner held 8–12 inches away. Avoid a pencil tip, which can pit the paver and blow out the joint. Natural stone such as travertine needs lower pressure.

Is mold on pavers dangerous?

Black and green growth on pavers is mostly a cosmetic and slip hazard, but people with asthma or mold allergies should wear a mask or have it cleaned for them. Cleaning removes it, and fixing the moisture source, such as shade, sprinklers or a downspout, keeps it from returning.

Do I have to re-sand pavers after pressure washing?

Yes, plan on it. A pressure washer strips joint sand along with the dirt, and low joints let pavers shift and let weeds and ants in. Let the pavers dry, refill the joints, then seal if you want sealer.

Can pavers be cleaned and re-sanded during the Florida rainy season?

You can clean and rinse, but joint sand and sealer need dry days to set, and summer afternoon storms get in the way. The most reliable window in Central Florida is roughly October through May.

Keep Reading

Related Guides

Free Paver Restoration Estimate — Ocoee & Orlando Area

Free written estimate · 7 days a week · No obligation

(689) 356-6292
Free Estimate Form